win98 and Dialer

[paolog]

Hi... I'm thinking that modems are not yet my friends ;-)

Due to the dialing problem on win2K (don't solved from my last topic) I decide to install wingate on a new machine. I have a new formatted win98SE machine, then I install wingate and then (due to driver finding problem) the ISDN I-courier robotics modem and setup IE connection.

Then I have configurated the dialer in wingate.. all fine.
At every machine reboot..... wingate tell me that dialer is changed, and that there is a new dialer to config.
I remake the WinGate dialer config all works.. until next reboot... same problem.
I have deleted and remade the connection of IE, and then again that one of wingate.. but the problem still persist.

What I can do ? because if the machine is rebooted by customer, wingate loose the capability to connect to ISP :(

thanks in advance

[paolog]

There are not solution also for this ? :(

something I can try ?

Log that you need, configuration file.... something....

[Pascal]

Once you've configured it, enabled it and set the profile to be enabled as well, click the Save Button. Then, in the registry, verify that the profile has been saved to the registry.

(HKEY_LOCAL_MACHINE\SOFTWARE\Qbik Software\WinGate\Dialer\Profiles)

That message will appear when WinGate find a dialer profile from the RAS subsystem that does not exist in its registry configuration. You can try enabling debug logging on the Dialer Subsystem as well, that should give us some more information.

[paolog]

This happen in dialer.log
03/30/04 20:16:51 Debug: Dialer thread started
03/30/04 20:16:52 Debug: Refreshing OS phonebook entries
03/30/04 20:16:53 Debug: CInterfaceChangeDetector: Interface PPP Adapter. (MAC 44-45-53-54-00-00, IP 0.0.0.0, type 23)

03/30/04 20:16:53 Debug: CInterfaceChangeDetector: Interface D-Link DFE-538TX 10/100 Adapter (MAC 00-50-BA-4E-7B-7A, IP 192.168.0.2, type 6)

03/30/04 20:16:53 Debug: CInterfaceChangeDetector: Interface PPP Adapter. (MAC 44-45-53-54-00-00, IP 0.0.0.0, type 23)

03/30/04 20:16:53 Debug: CInterfaceChangeDetector: Interface D-Link DFE-538TX 10/100 Adapter (MAC 00-50-BA-4E-7B-7A, IP 192.168.0.2, type 6)

03/30/04 20:16:53 Debug: CInterfaceChangeDetector: Interface PPP Adapter. (MAC 44-45-53-54-00-00, IP 0.0.0.0, type 23)

03/30/04 20:16:53 Debug: CInterfaceChangeDetector: Interface D-Link DFE-538TX 10/100 Adapter (MAC 00-50-BA-4E-7B-7A, IP 192.168.0.2, type 6)

03/30/04 20:17:30 Debug: Refreshing OS phonebook entries
03/30/04 20:17:30 Debug: ConnessioneISDN: Off line.



in registers, after reboot, the information of dialer are again correct (ie "user" is written with right information). But if I open dialer in wingate it will be blank. Rewriting data in form and saving, register data are changed with new values.

Something idea ?

[paolog]

Can be this, because machine ip is 192.168.0.2 and not 192.168.0.1 ?

I don't have any other idea ? is a problem on dialer or on network interface card ?

Best regards

[Pascal]

Check the registry key:

Code:

HKEY_LOCAL_MACHINE\SOFTWARE\Qbik Software\WinGate\Logging\Persisted

Are there any values in there ?

[paolog]

no, empty key